The M-Wave Classic Platform pedal is an excellent choice for restoring a classic. Steel axle along with exchangeable rubber blocks make this pedal. Contents • • • • A. When the golf cart’s brake pedal almost touches the floor Before starting to adjust the brakes, prepare this set of tools: • Adjustable wrench • ¾ inch socket wrench • 2 tons floor jack • 4 bricks or blocks Here are the steps in adjusting the brakes: • Turn off the power of the golf cart. Don’t set its parking brake. • Put the brick or blocks in front and behind each of the front wheel of the golf cart to prevent it from rolling. • Get the floor jack into position at the rear of the golf cart. The two rear wheels should be lifted simultaneously off the ground. • Use the socket wrench to loosen the lug nuts on the rear wheels. Remove the nuts and the wheels and set them aside. • Remove the rubber boots on the underside of the wheels and the brake adjustment screw will be exposed. Pull these rubber boots away from the wheels by using your hands. • Turn the adjustment screw in such a way that it is moving towards the wheel. This will cause the brake pads to move closer to the brake drum. You have corrected the brake adjustment if you feel that there is no more friction or resistance when you are turning the wheel by just using your hands. • Put the rubber boots back, as well as the wheels and then tighten the lug nuts to secure them in place. • Release the floor jack so that the golf cart wheels will again touch the floor. And then remove the bricks of blocks from the wheels in front. Adjusting the brakes on an E-Z-GO golf cart The brakes in an E-Z-GO golf cart are automatically adjusted by its mechanical rear drum braking system depending on the wear of the brake shoe. This is done while the golf cart is running. If you play enough, four more characters will be unlocked. The game starts with eight characters: Mario (Mario Bros.), DK (Donkey Kong), Link (Metroid Series), Yoshi (Super Mario World), Kirby (KIirby), Fox (Star Fox), and Pikachu (Pokemon). Was released back in 1999 for the N64 gaming console and sold over a million copies in Japan alone and even more Worldwide. Super smash bros brawl emulator online. But if the wear of the brake shoe is extensive, this system will turn a star wheel or a notch that will push the shoe nearer the drums. The stopping force will be induced by the contact between the drums and the shoes. The steps in adjusting the brakes are as follows: • Sit on the driver’s seat • Run the golf cart and accelerate up to its full speed but ensure that you have enough road space. • Once the cart is running full speed, step on the brakes. This should engage the braking system fully. Thomson reuters excel formulas. Release the brake pedals before the cart comes to a full stop. The golf cart’s automatic braking system will adjust the brakes while the cart is still moving. Adjusting the brake fluid travel The gap or space that the pedal travels as it moves from its default position to the point when the brake cables starts to power the brake levers is called the brake fluid travel. It is important to adjust this distance of travel to make sure that the brakes are working properly. If there is too much travel distance, the braking capacity or power of the golf cart will be reduced. But if the distance is too short, the brakes may not release fully. So adjustments are necessary in both cases. You can adjust the brake fluid travel by loosening the nut and then rotating the spherical nut. The nuts need to be properly torqued at 10 to 11 ft.-lbs. Or 14 – 15 Nm. The ideal setting for the brake fluid travel is from 7/8 inch to 1 and 1/8 inches or 2.2 to 2.9 cm. And then you need to immediately energize the brake pedal from 4 to 6 times in order to get the actual fluid travel. Then perform a dynamic test by running the cart slowly and energizing the brakes hard and quick. Repeat 10 times more so that the brakes will adjust freely. When finished, use the spherical nut to adjust the brake fluid travel. Run the cart again and brake hard and quick 10 more times. Check if the free travel of the fluid is not changing during braking. If it changes, continue the adjustments on the spherical nut and continue the test runs. In addition, you should also check if the clevis pins located at the end of the brake cables and levers are loose. Adjusting the brakes of old style golf carts If in case you are using some of the old style golf carts, here are some tips on how to adjust their brakes. Before starting the brake adjustment, disconnect the battery or the battery pack of the golf cart and prepare the necessary tools such as floor jack, bricks or blocks, wrench and so forth. Some of the old style golf carts may have run/low switches. These switches should be shifted to the tow position before disconnecting their battery packs. Lift the back of the golf cart and put the floor jack in a secure section of the cart which should provide it a stable support. Before starting the brake adjustment, it will be advisable for you to have a checklist on the steps that you need to take since there are several steps that you need to perform.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |